Exactly How to Replace a Tub Yourself: Removing and Replacing.
Exactly How to Replace a Tub Yourself: Removing and Replacing.
Blog Article
We have stumbled on the article relating to How to Install a Bathtub Yourself down the page on the internet and reckoned it made good sense to write about it with you on my blog.
Mounting a bath tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult project. If the old bathtub is easily available, the project can move easily; if you need to open a wall to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub and also embeded in the new one. See to it you have qualified on your own for the task and fit attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bathtub in your washroom if you have already acquired a brand-new tub and also don't require to alter the arrangement of your previous water pipelines.
Your tools and also product checklist need to make up the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the needed setting. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if required. Fill the bath tub as well as likewise check the overflow outlet and also the typical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been made use of a minimum of once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealer can fracture rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that article about How to Install a Bathtub through an associate on another web property. Do you know about somebody who is looking into the topic? Why not promote it. Kudos for your time. Don't hesitate to stop by our website back soon.
Schedule A Service Report this page